殼牌石油公司 --油氣分離器Gas Liquid Separators - Type Selection and Design Rules

wdyou

殼牌石油公司 --油氣分離器Gas Liquid Separators - Type Selection and Design Rules，非常好的資料，英文版的，需要的快下載

1. INTRODUCTION
        1.1 SCOPE
        1.2 SUMMARY OF CHANGES SINCE PREVIOUS EDITION
        1.3 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS
        1.4 DEFINITIONS
        1.5 CROSS-REFERENCES
        1.6 SYMBOLS AND ABBREVIATIONS
2. SELECTION CRITERIA FOR GAS/LIQUID SEPARATORS
        2.1 DUTY
        2.2 ORIENTATION
        2.3 COMPONENTS
        2.4 DESIGN BASE
        2.5 SELECTION STRATEGY
3. DESIGN RULES
        3.1 VERTICAL KNOCK-OUT DRUM
        3.2 HORIZONTAL KNOCK-OUT DRUM
        3.3 VERTICAL WIREMESH DEMISTER
        3.4 HORIZONTAL WIREMESH DEMISTER
        3.5 VERTICAL VANE-TYPE DEMISTER
        3.6 HORIZONTAL VANE-TYPE DEMISTER
        3.7 VERTICAL SEPARATOR WITH SWIRLTUBE DEMISTER DECK
        3.8 CYCLONE WITH TANGENTIAL INLET (CONVENTIONAL CYCLONE)
        3.9 CYCLONE WITH STRAIGHT INLET AND SWIRLER ("GASUNIE" CYCLONE)
        3.10 VERTICAL SEPARATOR WITH REVERSED-FLOW MULTICYCLONE BUNDLE (CONVENTIONAL MULTICYCLONE)
        3.11 VERTICAL SEPARATOR WITH AXIAL-FLOW MULTICYCLONE BUNDLE (WITH RECIRCULATION OF SECONDARY GAS)
        3.12 HORIZONTAL SEPARATOR WITH AXIAL-FLOW MULTICYCLONE BUNDLE (WITH RECIRCULATION OF SECONDARY GAS)
        3.13 FILTER SEPARATOR
4. PIPING REQUIREMENTS
5. REFERENCES

helloshigy

PREFACE

They are based on the experience acquired during their involvement with the design, construction, operation and
maintenance of processing units and facilities, and they are supplemented with the experience of Group Operating
companies. Where appropriate they are based on, or reference is made to, international, regional, national and industry
standards.
The objective is to set the recommended standard for good design and engineering practice applied by Group
companies operating an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other
such facility, and thereby to achieve maximum technical and economic benefit from standardization.
The information set forth in these publications is provided to users for their consideration and decision to implement.
This is of particular importance where DEPs may not cover every requirement or diversity of condition at each locality.
The system of DEPs is expected to be sufficiently flexible to allow individual operating companies to adapt the
information set forth in DEPs to their own environment and requirements.
When Contractors or Manufacturers/Suppliers use DEPs they shall be solely responsible for the quality of work and the
attainment of the required design and engineering standards. In particular, for those requirements not specifically
covered, the Principal will expect them to follow those design and engineering practices which will achieve the same
level of integrity as reflected in the DEPs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting
from his own responsibility, consult the Principal or its technical advisor.

helloshigy

APPENDICES
APPENDIX I NATURE OF THE FEED .................................................................................80
APPENDIX II SIZING OF THE FEED AND OUTLET NOZZLES ..........................................84
APPENDIX III DESIGN OF SCHOEPENTOETER (VANE-TYPE) INLET DEVICE ...............86
APPENDIX IV DESIGN MARGINS FOR SEPARATOR DESIGN ..........................................91
APPENDIX V LEVEL CONTROL...........................................................................................92
APPENDIX VI VESSEL GEOMETRICAL RELATIONSHIPS..................................................94
APPENDIX VII SIZING OF SEPARATOR VESSELS..............................................................98
APPENDIX VIII MISTMAT SPECIFICATIONS .......................................................................103
APPENDIX IX VANE PACKS................................................................................................104
APPENDIX X VESSEL SIZING EXAMPLES .......................................................................106
APPENDIX XI DEBOTTLENECKING TIPS ..........................................................................113

helloshigy

我給你加了內容  以后最好把目錄和一些文章內容寫到帖子里   這樣大家可看看 根據需要下載

wdyou

helloshigy 發表于 2017-2-4 08:54
我給你加了內容  以后最好把目錄和一些文章內容寫到帖子里   這樣大家可看看 根據需要下載

謝謝...........

tony802106

不知道是否詳細，感覺12J里太粗略了。。。

wdyou

tony802106 發表于 2017-2-4 11:30
不知道是否詳細，感覺12J里太粗略了。。。

還好，多結合幾個標準看看就好了，我感覺比那個20570要好多了

cosn

十幾年前的資料，希望還沒有過時，英文的看起來耗時。

wdyou

cosn 發表于 2017-2-5 21:01
十幾年前的資料，希望還沒有過時，英文的看起來耗時。

就是因為10幾年前的才珍貴，不懂別亂說

tomlu

已經有新版的了